RC6x, RC32, RC24 DirecTV remote programmingTo set up your DirecTV Remote to operate your TV, DVD or other devices you can use the on-screen method, or the manual procedures below:Manual code entryStep 1: Slide the mode switch to the DIRECTV, AV1, AV2 or TV position.Step 2: Press and hold the 'MUTE' and 'SELECT' keys at the same time until the green light under the selected mode flashes twice, then release both keys.Step 3: Using the number keys, enter the for the brand of component being set up. If the code is accepted, the green light under the selected position will flash twice.Step 4: Aim the remote at your device and press the 'PWR' key once.

1. Directv Remote Code For Onn Tv

The device should turn off. If not, repeat this procedure, trying each code for your brand until you find the correct one.Notes:.The AV1 and AV2 switch positions can be setup to control a, a second or a second.The RC32BB Big Button remote does not have a mode switch. Press and release the appropriate mode key instead for the device you want to program in Step 1. To enter programming mode press and hold the appropriate mode key until the green LED flashes twice in Step 2.To program an old Blue Universal Remote, press the appropriate mode button then press and hold 'Setup' until the mode key blinks twice. Type in the 4-digit code obtained from dropping the first digit from the recent 5-digit lists.

Note that fewer codes will work with this old remote.Code SearchIf you were unable to find a working code for your device, you can perform a code search. The process may take up to 30 minutes.Step 1: Turn on your device. Insert a tape or disk if applicable.Step 2: Slide the mode switch to the TV, AV1 or AV2 position, as desired.Step 3: Press and hold the 'MUTE' and 'SELECT' keys at the same time until the green light under the selected switch position flashes twice, then release both keys.Component typeID#Satellite0TV1VCR/DVD/PVR2Stereo3Step 4: Enter 9 9 1 followed by ID# of your type of device.Step 5: Press 'PWR' or other functions (e.g. 'PLAY' for VCR) you want to test for.Step 6: Point the remote at the TV or component and repeatedly press 'Channel Up' until your device turns off or performs the action you selected in step 5. If you accidentally pressed 'Channel Up' after your device responded press 'Channel Down' to step back a code.Step 7: When the device turns off or performs the action you selected in step 5, press and release the 'SELECT' key.Note: If the light flashes 3 times, you've cycled through all codes and the code for your device was not found. You must use the remote that came with your device.Finding out the codeOnce you have set up the DirecTV Universal Remote Control using Code Search, perform the following procedure to find out the 5-digit code to which your component responded:Step 1: Slide the mode switch to the appropriate position.Step 2: Press and hold the 'MUTE' and 'SELECT' keys at the same time until the green light under the selected switch position flashes twice, then release both keys.Step 3: Enter 9 9 0. The green light under the selected switch position will flash twice.Step 4: To view the first digit in the code, press and release the number '1' key.

Wait 3 seconds, and count the number of times the green light flashes. Write this number down. Repeat this step four more times for the remaining digits: press number '2' for the second digit, '3' for the third digit, '4' for the fourth digit and '5' for the final digit. Setting up the TV input keyOnce you have setup the DirecTV Remote control for your TV, you can activate the 'TV INPUT' key so you can change the 'Source' - the equipment whose signal you want to be displayed on your TV:Step 1: Slide the mode switch to the TV position.Step 2: Press and hold the 'MUTE' and 'SELECT' keys until the green light under the TV position flashes twice, then release both keys.Step 3: Using the number keys, enter 9 6 0.

The green light under the TV position flashes twice. You now can change the input for your TV.If you want to deactivate the 'TV INPUT' key, repeat the procedure above; the green light will blink 4 times and pressing the 'TV INPUT' key will now do nothing. Changing volume lockDepending on how you set up your remote, the 'VOL' and 'MUTE' may control the volume on your TV, regardless of the position of the mode switch. This remote can be set up so that the 'VOL' and 'MUTE' keys work only with the component selected by the mode switch.

To enable this feature, perform the following steps:Step 1: Press and hold the 'MUTE' and 'SELECT' keys until the green light under the DIRECTV position flashes twice, then release both keys.Step 2: Using the number keys, enter 9 9 3. The green light will flash twice.Step 3: Press and release the 'VOL+' key. The green light will flash 4 times.

Now the 'VOL' and 'MUTE' keys will work only for the component selected by the mode switch position.Locking volume to AV1, AV2 or TVStep 1: Slide the mode switch to the AV1, AV2 or TV position you want to lock the volume to.Step 2: Press and hold the 'MUTE' and 'SELECT' keys until the green light under the selected mode flashes twice, then release both keys.Step 3: Using the number keys, enter 9 9 3. The green light will flash twice.Step 4: Press and release the 'SELECT' key. The green light will flash twice.Note: DirecTV Receivers don't have volume control, so the remote will not allow the user to lock volume to the DIRECTV mode.

Activating and deactivating the RF transmitterMost DirecTV Remote Controls (e.g., RC32RF, RC64R/RB, RC65R/RX/RB/RBX, RC66RBX, RC80HB) have RF (Radio Frequency) capability. When you activate the RF feature of your remote control, you can control your DirecTV Receiver from anywhere in your home. You do not need to be within the line of sight of your receiver to control it. Note that not all DirecTV Receivers are RF-capable.If your receiver requires an external RF antenna, before activating the RF transmitter, locate the RF antenna included with your remote control and insert it into the RF remote antenna coaxial connector on the back of your DirecTV Receiver.Activating the RF transmitterTo activate the RF transmitter on your DirecTV Remote Control, perform the following steps:Step 1: Locate the 12 digit Receiver ID (RID) number of your DIRECTV Receiver. You can find the RID number on the back panel of your receiver, or inside the CAM access door next to the reset button.Step 2: Write down the last 6 digits of the RID number.Step 3: Slide the mode switch to DIRECTV, AV1 or AV2.Step 4: Press and hold the 'MUTE' and 'SELECT' keys until the green light under the selected switch flashes twice, then release both keys.Step 5: Using the number keys, enter 9 6 1. The green light will flash twice.Step 6: Press and release 'Channel Up'. The green light will flash twice.Step 7: Using the number keys, enter the last 6 digits of the RID number.Step 8: Press and release the 'SELECT' key.

The green light will flash twice.Deactivating the RF TransmitterTo deactivate the RF transmitter on your DirecTV Remote Control, perform the following steps:Step 1: Slide the mode switch to DIRECTV, AV1, or AV2.Step 2: Press and hold the 'MUTE' and 'SELECT' keys until the green light under the selected switch flashes twice, then release both keys.Step 3: Using the number keys, enter 9 6 1. The green light will flash twice.Step 4: Press and release 'Channel Down'. The green light will flash twice. The RF transmitter on your remote control is now deactivated.

Sometimes even a labor-saving device needs a little something to get started. In the case of your DIRECTV Universal Remote, all you’ll have to do is enter some information and press a few buttons.DIRECTV offers two types of these devices: the Standard Universal Remote and the Universal RF Remote.

Both models allow you to control up to 4 entertainment components, including your DIRECTV receiver, television, DVD player and VCR.You have two options for programming your DIRECTV Universal Remote, on-screen and manual. On-screen programmingThis programming method displays an easy, step-by-step guide on your TV screen. Press the MENU button on the remote. Select Settings & Help.

Directv Remote Code For Onn Tv

Select Settings. Select Remote Control. Select Program Remote. Follow the directions that appear on-screen.Manual programmingFollow these steps to program your DIRECTV Universal Remote manually.After turning on the TV and receiver, the next steps are:. Look up the 5-digit code for your brand of TV.

Patch fifa 2009 liga 1 transferuri 2012851836. Aceasta este cea de-a doua versiune a patchului RLSP 2009, patch ce adauga campionatele romanesti de fotbal in Fifa 09. FifaRomania - Liga 1 in Fifa.

You can find a list of the codes by brand on the DIRECTV website. Find the MODE switch on the remote control and slide it to the TV position. Press and hold MUTE and SELECT buttons simultaneously. Release the buttons after the green light at the top of the remote flashes twice. Enter the 5-digit code. Look for the green light under the TV to flash twice.

Aiming the remote at the television, press VOLUME UP. (If the volume doesn’t increase, try a different code and repeat steps 2-4. The DIRECTV website has a list of instructions to scan for additional codes. When the volume increases, proceed to step 6.). Again pressing MUTE and SELECT simultaneously, look for the green light at the top of the remote control to flash twice. Using the remote control keypad, enter the number 960. The same green light on the remote should flash twice again.

Move the MODE switch to the DIRECTV position.If you need additional help, try the Help Center on the DIRECTV website. You can look up frequently asked questions, consult interactive guides and more.Once you’ve programmed your universal remote control, start enjoying the exceptional lineup of DIRECTV programming.